-
$0.00
- No products in the cart.
Cowboy Action
Showing 1–12 of 42 results
-
.32 H&R Magnum 78 Grain RN Red Hi-Tek Coated Lead Cowboy Action-
With our 100% hand-loading techniques- We place the same care and passion into each and every round produced as those do in their own private loading rooms. These techniques produce the most reliable, accurate round of ammunition available on the market today! The .32 H&R Cowboy Action load is developed for Cowboy Action Shooters by Cowboy Action (SASS) Shooters. Our mild shooting Cowboy Action line meets SASS Power Factors, yet are a pleasure to shoot in repetition with minimal kick back or recoil.
Cowboy Choice Ammunition is an affiliated SASS Merchant, recognized as a leader in true Cowboy Action Ammunition. Visit the Single Action Shooting Society website at: http://www.sassnet.com/
We use a unique heat-set “HI-TEK Supercoat” manufactured in Australia, where it has been used for more than 20 years. The Hi-Tek Supercoat Bullet Coating totally encapsulates the lead projectiles and replaces standard wax lube. These .38 Special Cowboy Action Hi-Tek Coated Lead 105 grain TCFP rounds feed reliably in Lever Guns as well.Hi-Tek Supercoat bullets are safe to shoot indoors. The coating gives off no toxic out-gassing or particulate matter when fired. The coating is absolutely nonabrasive and contains no PTFE or MOLY. There is no wax lube and it minimizes your exposure to lead. The end result is cleaner air, cleaner hands, cleaner equipment and cleaner guns!Check out a video of the Hi-Tek coating process here and see why you might want us to do it for you!!- Velocity: 820 FPS
- Meets SASS Power Factor.
- Sized: .312
- OAL: 1.350”
- Federal Primers!
- Approved for Indoor Ranges!
- 100% Hand-Loaded
- Power Factor: 64
- BHN 12/15
- Our bullets greatly reduce the amount of smoke normally associated with cast bullets
- Lead fouling of the bore is drastically reduced or in most cases, eliminated completely
- Our coating gives off no toxins or particulate matter when fired
- Is 100% non abrasive and contains no PTFE or MOLY
- Greatly minimizes your exposure to lead
Add to cart19 in stock (can be backordered)
-
.357 Magnum Cowboy Action Hi-Tek Coated Lead 158 grain RNFP- With our 100% hand-loading techniques- We place the same care and passion into each and every round produced as those do in their own private loading rooms. These techniques produce the most reliable, accurate round of ammunition available on the market today! The .38 Special Cowboy Action line is developed for Cowboy Action Shooters by Cowboy Action (SASS) Shooters. Our mild shooting Cowboy Action line meets SASS Power Factors, yet are a pleasure to shoot in repetition with minimal kick back or recoil.
Cowboy Choice Ammunition is an affiliated SASS Merchant, recognized as a leader in true Cowboy Action Ammunition. Visit the Single Action Shooting Society website at: http://www.sassnet.com/
We use a unique heat-set “HI-TEK Supercoat” manufactured in Australia, where it has been used for more than 20 years. The Hi-Tek Supercoat Bullet Coating totally encapsulates the lead projectiles and replaces standard wax lube. These .38 Special Cowboy Action Hi-Tek Coated Lead 158 grain RNFP rounds feed reliably in Lever Guns as well.Our bullets are “Hard-Cast.” Hard cast bullets are just that: harder. We use a 92% Lead/6% Antimony/2% Tin bullet alloy for casting all bullets.Hi-Tek Supercoat bullets are safe to shoot indoors. The coating gives off no toxic out-gassing or particulate matter when fired. The coating is absolutely nonabrasive and contains no PTFE or MOLY. There is no wax lube and it minimizes your exposure to lead. The end result is cleaner air, cleaner hands, cleaner equipment and cleaner guns!Check out a video of the Hi-Tek coating process here and see why you might want us to do it for you!!Approved for Indoor Ranges!
May not feed in lever guns particular to overall length.
- Our bullets greatly reduce the amount of smoke normally associated with cast bullets
- Lead fouling of the bore is drastically reduced or in most cases, eliminated completely
- Our coating gives off no toxins or particulate matter when fired
- Is 100% non abrasive and contains no PTFE or MOLY
- They are completely safe to use in Glock’s polygonal rifled barrels
- There is no risk of receiving bullets, only to find that the lube has melted or shaken out of the lube groove
- Greatly minimizes your exposure to lead
Sized: .358
Velocity: FPS 615
Power Factor: 97
OAL: 1.56
Add to cart206 in stock (can be backordered)
-
.357 Magnum Cowboy Action Hi-Tek Coated Lead 125 grain RNFP- With our 100% hand-loading techniques- We place the same care and passion into each and every round produced as those do in their own private loading rooms. These techniques produce the most reliable, accurate round of ammunition available on the market today! The .357 Magnum “Cowboy Choice” line is developed for Cowboy Action Shooters by Cowboy Action (SASS) Shooters! Our mild shooting Cowboy Action line meets SASS Power Factors, yet are a pleasure to shoot in repetition with minimal kick back or recoil.
Cowboy Choice Ammunition is an affiliated SASS Merchant, recognized as a leader in true Cowboy Action Ammunition. Visit the Single Action Shooting Society website at: http://www.sassnet.com/
We use a unique heat-set “HI-TEK Supercoat” manufactured in Australia, where it has been used for more than 20 years. The Hi-Tek Supercoat Bullet Coating totally encapsulates the lead projectiles and replaces standard wax lube. These .357 Magnum Cowboy Action Hi-Tek Coated Lead 125 grain RNFP rounds feed reliably in Lever Guns as well.Our bullets are “Hard-Cast.” Hard cast bullets are just that: harder. We use a 92% Lead/6% Antimony/2% Tin bullet alloy for casting all bullets.Hi-Tek Supercoat bullets are safe to shoot indoors. The coating gives off no toxic out-gassing or particulate matter when fired. The coating is absolutely nonabrasive and contains no PTFE or MOLY. There is no wax lube and it minimizes your exposure to lead. The end result is cleaner air, cleaner hands, cleaner equipment and cleaner guns!Check out a video of the Hi-Tek coating process here and see why you might want us to do it for you!!- Velocity: 720 FPS
- Power Factor: 90
- OAL: 1.485″
- BHN 12/15
- Approved for Indoor Ranges!
- Our bullets greatly reduce the amount of smoke normally associated with cast bullets
- Lead fouling of the bore is drastically reduced or in most cases, eliminated completely
- Our coating gives off no toxins or particulate matter when fired
- Is 100% non abrasive and contains no PTFE or MOLY
- They are completely safe to use in Glock’s polygonal rifled barrels
- There is no risk of receiving bullets, only to find that the lube has melted or shaken out of the lube groove
- Greatly minimizes your exposure to lead
Add to cart251 in stock (can be backordered)
-
.357 Magnum Cowboy Action Hi-Tek Coated Lead 125 grain TCFP– With our 100% hand-loading techniques- We place the same care and passion into each and every round produced as those do in their own private loading rooms. These techniques produce the most reliable, accurate round of ammunition available on the market today! The .38 Special “Cowboy Choice” line is developed for Cowboy Action Shooters by Cowboy Action (SASS) Shooters! Our mild shooting Cowboy Action line meets SASS Power Factors, yet are a pleasure to shoot in repetition with minimal kick back or recoil.
Cowboy Choice Ammunition is an affiliated SASS Merchant, recognized as a leader in true Cowboy Action Ammunition. Visit the Single Action Shooting Society website at: http://www.sassnet.com/
We use a unique heat-set “HI-TEK Supercoat” manufactured in Australia, where it has been used for more than 20 years. The Hi-Tek Supercoat Bullet Coating totally encapsulates the lead projectiles and replaces standard wax lube. These .357 Magnum Cowboy Action Hi-Tek Coated Lead 125 grain TCFP rounds feed reliably in Lever Guns as well.Our bullets are “Hard-Cast.” Hard cast bullets are just that: harder. We use a 92% Lead/6% Antimony/2% Tin bullet alloy for casting all bullets.Hi-Tek Supercoat bullets are safe to shoot indoors. The coating gives off no toxic out-gassing or particulate matter when fired. The coating is absolutely nonabrasive and contains no PTFE or MOLY. There is no wax lube and it minimizes your exposure to lead. The end result is cleaner air, cleaner hands, cleaner equipment and cleaner guns!Check out a video of the Hi-Tek coating process here and see why you might want us to do it for you!!Velocity: 650 FPS
Power Factor: 81
OAL: 1.575″
BHN 12/15
Approved for Indoor Ranges!
- Our bullets greatly reduce the amount of smoke normally associated with cast bullets
- Lead fouling of the bore is drastically reduced or in most cases, eliminated completely
- Our coating gives off no toxins or particulate matter when fired
- Is 100% non abrasive and contains no PTFE or MOLY
- They are completely safe to use in Glock’s polygonal rifled barrels
- There is no risk of receiving bullets, only to find that the lube has melted or shaken out of the lube groove
- Greatly minimizes your exposure to lead
Add to cart383 in stock (can be backordered)
-
.38 Long Colt 105 Grain TCFP Hi-Tec Coated Lead Cast Bullet in “COWBOY CHOICE- The .38 Long Colt, also known as .38 LC, is a black powder cartridge introduced by Colt’s Manufacturing Company in 1875. In 1892, it was adopted as a standard military pistol cartridge by the United States Army for the Colt M1892 revolver. The metric designation for the .38 Long Colt is 9.1×26mm. It is slightly more powerful than the .38 Short Colt, also known as .38 SC. The original .38 SC and .38 LC differ in case length, bullet diameter, weight, and design and are not interchangeable; however, modern production .38 SC ammunition is now loaded with a smaller, internally-lubricated bullet which can be fired from firearms chambered in .38 LC or .38 Special. The modern .38 LC can be fired from .38 Special firearm, but not from a firearm designed for the .38 SC, since the case length is too long.
The .38 Long Colt remained the Army’s primary revolver cartridge until 1909, when the .45 M1909 cartridge was issued along with the .45 Colt New Service revolver as the new standard military sidearm for the U.S. Army. However, some of the old .38 Long Colt revolvers and ammunition remained in reserve stocks, and when the U.S. entered World War I in 1917, the need for sidearms was such that even these low-performing weapons were brought out of storage for usage away from the front lines.
In civilian use, the .38 LC was chambered in a number of Colt revolvers and saw some use among target shooters. Various U.S. police forces also adopted the cartridge. However, the cartridge became nearly extinct after Smith & Wesson‘s more powerful .38 Special cartridge became widely popular as a civilian and police service cartridge. By 1908, even Colt was chambering their new Police Positive and Army Special revolvers in “.38 Colt Special”, which was just a standard .38 Smith & Wesson Special with a different headstamp. *From Wikipedia, the free encyclopedia
COWBOY CHOICE AMMUNITION
Cowboy Choice Ammunition is an affiliated SASS Merchant, recognized as a leader in true Cowboy Action Ammunition. Visit the Single Action Shooting Society website at: http://www.sassnet.com/
We use a unique heat-set “HI-TEK Supercoat” manufactured in Australia, where it has been used for more than 20 years. The Hi-Tek Supercoat Bullet Coating totally encapsulates the lead projectiles and replaces standard wax lube. These .38 Special Cowboy Action Hi-Tek Coated Lead 105 grain TCFP rounds feed reliably in Lever Guns as well.Our bullets are “Hard-Cast.” Hard cast bullets are just that: harder. We use a 92% Lead/6% Antimony/2% Tin bullet alloy for casting all bullets.Hi-Tek Supercoat bullets are safe to shoot indoors. The coating gives off no toxic out-gassing or particulate matter when fired. The coating is absolutely nonabrasive and contains no PTFE or MOLY. There is no wax lube and it minimizes your exposure to lead. The end result is cleaner air, cleaner hands, cleaner equipment and cleaner guns!Check out a video of the Hi-Tek coating process here and see why you might want us to do it for you!!Velocity: 640 FPS
Approved for Indoor Ranges!
100% Hand-Loaded
-
.38 Long Colt 105 Grain TCFP Hi-Tec Coated Lead Cast Bullet in “COWBOY CHOICE- The .38 Long Colt, also known as .38 LC, is a black powder cartridge introduced by Colt’s Manufacturing Company in 1875. In 1892, it was adopted as a standard military pistol cartridge by the United States Army for the Colt M1892 revolver. The metric designation for the .38 Long Colt is 9.1×26mm. It is slightly more powerful than the .38 Short Colt, also known as .38 SC. The original .38 SC and .38 LC differ in case length, bullet diameter, weight, and design and are not interchangeable; however, modern production .38 SC ammunition is now loaded with a smaller, internally-lubricated bullet which can be fired from firearms chambered in .38 LC or .38 Special. The modern .38 LC can be fired from .38 Special firearm, but not from a firearm designed for the .38 SC, since the case length is too long.
The .38 Long Colt remained the Army’s primary revolver cartridge until 1909, when the .45 M1909 cartridge was issued along with the .45 Colt New Service revolver as the new standard military sidearm for the U.S. Army. However, some of the old .38 Long Colt revolvers and ammunition remained in reserve stocks, and when the U.S. entered World War I in 1917, the need for sidearms was such that even these low-performing weapons were brought out of storage for usage away from the front lines.
In civilian use, the .38 LC was chambered in a number of Colt revolvers and saw some use among target shooters. Various U.S. police forces also adopted the cartridge. However, the cartridge became nearly extinct after Smith & Wesson‘s more powerful .38 Special cartridge became widely popular as a civilian and police service cartridge. By 1908, even Colt was chambering their new Police Positive and Army Special revolvers in “.38 Colt Special”, which was just a standard .38 Smith & Wesson Special with a different headstamp. *From Wikipedia, the free encyclopedia
COWBOY CHOICE AMMUNITION
Cowboy Choice Ammunition is an affiliated SASS Merchant, recognized as a leader in true Cowboy Action Ammunition. Visit the Single Action Shooting Society website at: http://www.sassnet.com/
We use a unique heat-set “HI-TEK Supercoat” manufactured in Australia, where it has been used for more than 20 years. The Hi-Tek Supercoat Bullet Coating totally encapsulates the lead projectiles and replaces standard wax lube. These .38 Special Cowboy Action Hi-Tek Coated Lead 105 grain TCFP rounds feed reliably in Lever Guns as well.Our bullets are “Hard-Cast.” Hard cast bullets are just that: harder. We use a 92% Lead/6% Antimony/2% Tin bullet alloy for casting all bullets.Hi-Tek Supercoat bullets are safe to shoot indoors. The coating gives off no toxic out-gassing or particulate matter when fired. The coating is absolutely nonabrasive and contains no PTFE or MOLY. There is no wax lube and it minimizes your exposure to lead. The end result is cleaner air, cleaner hands, cleaner equipment and cleaner guns!Check out a video of the Hi-Tek coating process here and see why you might want us to do it for you!!Velocity: 640 FPS
Approved for Indoor Ranges!
100% Hand-Loaded
-
.38 Long Colt 125 Grain TCFP Hi-Tec Coated Lead Cast Bullet in “COWBOY CHOICE- The .38 Long Colt, also known as .38 LC, is a black powder cartridge introduced by Colt’s Manufacturing Company in 1875. In 1892, it was adopted as a standard military pistol cartridge by the United States Army for the Colt M1892 revolver. The metric designation for the .38 Long Colt is 9.1×26mm. It is slightly more powerful than the .38 Short Colt, also known as .38 SC. The original .38 SC and .38 LC differ in case length, bullet diameter, weight, and design and are not interchangeable; however, modern production .38 SC ammunition is now loaded with a smaller, internally-lubricated bullet which can be fired from firearms chambered in .38 LC or .38 Special. The modern .38 LC can be fired from .38 Special firearm, but not from a firearm designed for the .38 SC, since the case length is too long.
The .38 Long Colt remained the Army’s primary revolver cartridge until 1909, when the .45 M1909 cartridge was issued along with the .45 Colt New Service revolver as the new standard military sidearm for the U.S. Army. However, some of the old .38 Long Colt revolvers and ammunition remained in reserve stocks, and when the U.S. entered World War I in 1917, the need for sidearms was such that even these low-performing weapons were brought out of storage for usage away from the front lines.
In civilian use, the .38 LC was chambered in a number of Colt revolvers and saw some use among target shooters. Various U.S. police forces also adopted the cartridge. However, the cartridge became nearly extinct after Smith & Wesson‘s more powerful .38 Special cartridge became widely popular as a civilian and police service cartridge. By 1908, even Colt was chambering their new Police Positive and Army Special revolvers in “.38 Colt Special”, which was just a standard .38 Smith & Wesson Special with a different headstamp. *From Wikipedia, the free encyclopedia
COWBOY CHOICE AMMUNITION
Cowboy Choice Ammunition is an affiliated SASS Merchant, recognized as a leader in true Cowboy Action Ammunition. Visit the Single Action Shooting Society website at: http://www.sassnet.com/
We use a unique heat-set “HI-TEK Supercoat” manufactured in Australia, where it has been used for more than 20 years. The Hi-Tek Supercoat Bullet Coating totally encapsulates the lead projectiles and replaces standard wax lube. These .38 Special Cowboy Action Hi-Tek Coated Lead 105 grain TCFP rounds feed reliably in Lever Guns as well.Our bullets are “Hard-Cast.” Hard cast bullets are just that: harder. We use a 92% Lead/6% Antimony/2% Tin bullet alloy for casting all bullets.Hi-Tek Supercoat bullets are safe to shoot indoors. The coating gives off no toxic out-gassing or particulate matter when fired. The coating is absolutely nonabrasive and contains no PTFE or MOLY. There is no wax lube and it minimizes your exposure to lead. The end result is cleaner air, cleaner hands, cleaner equipment and cleaner guns!Check out a video of the Hi-Tek coating process here and see why you might want us to do it for you!!Velocity: 600 FPS
Approved for Indoor Ranges!
100% Hand-Loaded
- Our bullets greatly reduce the amount of smoke normally associated with cast bullets
- Lead fouling of the bore is drastically reduced or in most cases, eliminated completely
- Our coating gives off no toxins or particulate matter when fired
- Is 100% non abrasive and contains no PTFE or MOLY
- They are completely safe to use in Glock’s polygonal rifled barrels
- Greatly minimizes your exposure to lead
-
.38 Long Colt 125 Grain TCFP Hi-Tec Coated Lead Cast Bullet in “COWBOY CHOICE- The .38 Long Colt, also known as .38 LC, is a black powder cartridge introduced by Colt’s Manufacturing Company in 1875. In 1892, it was adopted as a standard military pistol cartridge by the United States Army for the Colt M1892 revolver. The metric designation for the .38 Long Colt is 9.1×26mm. It is slightly more powerful than the .38 Short Colt, also known as .38 SC. The original .38 SC and .38 LC differ in case length, bullet diameter, weight, and design and are not interchangeable; however, modern production .38 SC ammunition is now loaded with a smaller, internally-lubricated bullet which can be fired from firearms chambered in .38 LC or .38 Special. The modern .38 LC can be fired from .38 Special firearm, but not from a firearm designed for the .38 SC, since the case length is too long.
The .38 Long Colt remained the Army’s primary revolver cartridge until 1909, when the .45 M1909 cartridge was issued along with the .45 Colt New Service revolver as the new standard military sidearm for the U.S. Army. However, some of the old .38 Long Colt revolvers and ammunition remained in reserve stocks, and when the U.S. entered World War I in 1917, the need for sidearms was such that even these low-performing weapons were brought out of storage for usage away from the front lines.
In civilian use, the .38 LC was chambered in a number of Colt revolvers and saw some use among target shooters. Various U.S. police forces also adopted the cartridge. However, the cartridge became nearly extinct after Smith & Wesson‘s more powerful .38 Special cartridge became widely popular as a civilian and police service cartridge. By 1908, even Colt was chambering their new Police Positive and Army Special revolvers in “.38 Colt Special”, which was just a standard .38 Smith & Wesson Special with a different headstamp. *From Wikipedia, the free encyclopedia
COWBOY CHOICE AMMUNITION
Cowboy Choice Ammunition is an affiliated SASS Merchant, recognized as a leader in true Cowboy Action Ammunition. Visit the Single Action Shooting Society website at: http://www.sassnet.com/
We use a unique heat-set “HI-TEK Supercoat” manufactured in Australia, where it has been used for more than 20 years. The Hi-Tek Supercoat Bullet Coating totally encapsulates the lead projectiles and replaces standard wax lube. These .38 Special Cowboy Action Hi-Tek Coated Lead 105 grain TCFP rounds feed reliably in Lever Guns as well.Our bullets are “Hard-Cast.” Hard cast bullets are just that: harder. We use a 92% Lead/6% Antimony/2% Tin bullet alloy for casting all bullets.Hi-Tek Supercoat bullets are safe to shoot indoors. The coating gives off no toxic out-gassing or particulate matter when fired. The coating is absolutely nonabrasive and contains no PTFE or MOLY. There is no wax lube and it minimizes your exposure to lead. The end result is cleaner air, cleaner hands, cleaner equipment and cleaner guns!Check out a video of the Hi-Tek coating process here and see why you might want us to do it for you!!Velocity: 600 FPS
Approved for Indoor Ranges!
100% Hand-Loaded
- Our bullets greatly reduce the amount of smoke normally associated with cast bullets
- Lead fouling of the bore is drastically reduced or in most cases, eliminated completely
- Our coating gives off no toxins or particulate matter when fired
- Is 100% non abrasive and contains no PTFE or MOLY
- They are completely safe to use in Glock’s polygonal rifled barrels
- Greatly minimizes your exposure to lead
-
38 Special 105 Grain TCFP BLACK Hi-Tek Coated Lead Cowboy Action- With our 100% hand-loading techniques- We place the same care and passion into each and every round produced as those do in their own private loading rooms. These techniques produce the most reliable, accurate round of ammunition available on the market today! The .38 Special Cowboy Action line is developed for Cowboy Action Shooters by Cowboy Action (SASS) Shooters. Our mild shooting Cowboy Action line meets SASS Power Factors, yet are a pleasure to shoot in repetition with minimal kick back or recoil.
Cowboy Choice Ammunition is an affiliated SASS Merchant, recognized as a leader in true Cowboy Action Ammunition. Visit the Single Action Shooting Society website at: http://www.sassnet.com/
We use a unique heat-set “HI-TEK Supercoat” manufactured in Australia, where it has been used for more than 20 years. The Hi-Tek Supercoat Bullet Coating totally encapsulates the lead projectiles and replaces standard wax lube. These .38 Special Cowboy Action Hi-Tek Coated Lead 105 grain TCFP rounds feed reliably in Lever Guns as well.Our bullets are “Hard-Cast.” Hard cast bullets are just that: harder. We use a 92% Lead/6% Antimony/2% Tin bullet alloy for casting all bullets.Hi-Tek Supercoat bullets are safe to shoot indoors. The coating gives off no toxic out-gassing or particulate matter when fired. The coating is absolutely nonabrasive and contains no PTFE or MOLY. There is no wax lube and it minimizes your exposure to lead. The end result is cleaner air, cleaner hands, cleaner equipment and cleaner guns!Check out a video of the Hi-Tek coating process here and see why you might want us to do it for you!!Velocity: 650 FPS
OAL: 1.445”
Approved for Indoor Ranges!
100% Hand-Loaded
- Our bullets greatly reduce the amount of smoke normally associated with cast bullets
- Lead fouling of the bore is drastically reduced or in most cases, eliminated completely
- Our coating gives off no toxins or particulate matter when fired
- Is 100% non abrasive and contains no PTFE or MOLY
- They are completely safe to use in Glock’s polygonal rifled barrels
- Greatly minimizes your exposure to lead
- Meets SASS Power Factor.
- Sized: .358
- OAL: 1.445”
- Velocity: 650 FPS
- Power Factor: 68
- BHN 12/15
- Federal Primers !!
Add to cart629 in stock (can be backordered)
-
.38 Special 125 Grain TCFP BLACK Hi-Tek Coated Lead Cowboy Action- With our 100% hand-loading techniques- We place the same care and passion into each and every round produced as those do in their own private loading rooms. These techniques produce the most reliable, accurate round of ammunition available on the market today! The .38 Special Cowboy Action line is developed for Cowboy Action Shooters by Cowboy Action (SASS) Shooters. Our mild shooting Cowboy Action line meets SASS Power Factors, yet are a pleasure to shoot in repetition with minimal kick back or recoil.
Cowboy Choice Ammunition is an affiliated SASS Merchant, recognized as a leader in true Cowboy Action Ammunition. Visit the Single Action Shooting Society website at: http://www.sassnet.com/
We use a unique heat-set “HI-TEK Supercoat” manufactured in Australia, where it has been used for more than 20 years. The Hi-Tek Supercoat Bullet Coating totally encapsulates the lead projectiles and replaces standard wax lube. These .38 Special Cowboy Action Hi-Tek Coated Lead 125 grain TCFP rounds feed reliably in Lever Guns as well.Our bullets are “Hard-Cast.” Hard cast bullets are just that: harder. We use a 92% Lead/6% Antimony/2% Tin bullet alloy for casting all bullets.Hi-Tek Supercoat bullets are safe to shoot indoors. The coating gives off no toxic out-gassing or particulate matter when fired. The coating is absolutely nonabrasive and contains no PTFE or MOLY. There is no wax lube and it minimizes your exposure to lead. The end result is cleaner air, cleaner hands, cleaner equipment and cleaner guns!Check out a video of the Hi-Tek coating process here and see why you might want us to do it for you!!- Velocity: 640 FPS
- Power Factor: 80
- OAL: 1.450″
- BHN 12/15
- Approved for Indoor Ranges!
- 100% Hand-Loaded
- Our bullets greatly reduce the amount of smoke normally associated with cast bullets
- Lead fouling of the bore is drastically reduced or in most cases, eliminated completely
- Our coating gives off no toxins or particulate matter when fired
- Is 100% non abrasive and contains no PTFE or MOLY
- They are completely safe to use in Glock’s polygonal rifled barrels
- Greatly minimizes your exposure to lead
Add to cart386 in stock (can be backordered)
-
.38 Special Cowboy Action Hi-Tek Coated Lead 125 grain RNFP- With our 100% hand-loading techniques- We place the same care and passion into each and every round produced as those do in their own private loading rooms. These techniques produce the most reliable, accurate round of ammunition available on the market today! The .38 Special Cowboy Action line is developed for Cowboy Action Shooters by Cowboy Action (SASS) Shooters. Our mild shooting Cowboy Action line meets SASS Power Factors, yet are a pleasure to shoot in repetition with minimal kick back or recoil.
Cowboy Choice Ammunition is an affiliated SASS Merchant, recognized as a leader in true Cowboy Action Ammunition. Visit the Single Action Shooting Society website at: http://www.sassnet.com/
We use a unique heat-set “HI-TEK Supercoat” manufactured in Australia, where it has been used for more than 20 years. The Hi-Tek Supercoat Bullet Coating totally encapsulates the lead projectiles and replaces standard wax lube.Our bullets are “Hard-Cast.” Hard cast bullets are just that: harder. We use a 92% Lead/6% Antimony/2% Tin bullet alloy for casting all bullets.Hi-Tek Supercoat bullets are safe to shoot indoors. The coating gives off no toxic out-gassing or particulate matter when fired. The coating is absolutely nonabrasive and contains no PTFE or MOLY. There is no wax lube and it minimizes your exposure to lead. The end result is cleaner air, cleaner hands, cleaner equipment and cleaner guns!Check out a video of the Hi-Tek coating process here and see why you might want us to do it for you!!- Velocity: 690 FPS
- Power Factor: 86
- AOL: 1.350″
- Approved for Indoor Ranges!
- Our bullets greatly reduce the amount of smoke normally associated with cast bullets
- Lead fouling of the bore is drastically reduced or in most cases, eliminated completely
- Our coating gives off no toxins or particulate matter when fired
- Is 100% non abrasive and contains no PTFE or MOLY
- They are completely safe to use in Glock’s polygonal rifled barrels
- Greatly minimizes your exposure to lead
Add to cart133 in stock (can be backordered)
-
.38 Special Cowboy Action Hi-Tek Coated Lead 158 grain RNFP- With our 100% hand-loading techniques- We place the same care and passion into each and every round produced as those do in their own private loading rooms. These techniques produce the most reliable, accurate round of ammunition available on the market today! The .38 Special Cowboy Action line is developed for Cowboy Action Shooters by Cowboy Action (SASS) Shooters. Our mild shooting Cowboy Action line meets SASS Power Factors, yet are a pleasure to shoot in repetition with minimal kick back or recoil.
Cowboy Choice Ammunition is an affiliated SASS Merchant, recognized as a leader in true Cowboy Action Ammunition. Visit the Single Action Shooting Society website at: http://www.sassnet.com/
We use a unique heat-set “HI-TEK Supercoat” manufactured in Australia, where it has been used for more than 20 years. The Hi-Tek Supercoat Bullet Coating totally encapsulates the lead projectiles and replaces standard wax lube. These .38 Special Cowboy Action Hi-Tek Coated Lead 158 grain RNFP rounds feed reliably in Lever Guns as well.Our bullets are “Hard-Cast.” Hard cast bullets are just that: harder. We use a 92% Lead/6% Antimony/2% Tin bullet alloy for casting all bullets.Hi-Tek Supercoat bullets are safe to shoot indoors. The coating gives off no toxic out-gassing or particulate matter when fired. The coating is absolutely nonabrasive and contains no PTFE or MOLY. There is no wax lube and it minimizes your exposure to lead. The end result is cleaner air, cleaner hands, cleaner equipment and cleaner guns!Check out a video of the Hi-Tek coating process here and see why you might want us to do it for you!!Velocity: 590 FPS
Power Factor: 93
AOL: 1.420″
Approved for Indoor Ranges!
100% Hand-Loaded !!
- Our bullets greatly reduce the amount of smoke normally associated with cast bullets
- Lead fouling of the bore is drastically reduced or in most cases, eliminated completely
- Our coating gives off no toxins or particulate matter when fired
- Is 100% non abrasive and contains no PTFE or MOLY
- They are completely safe to use in Glock’s polygonal rifled barrels
- Greatly minimizes your exposure to lead
Add to cart203 in stock (can be backordered)
Showing 1–12 of 42 results